[pvrusb2] 29xxx pvrusb2 device initialization problems

[Steven Karp]

On Friday 05 February 2010 at 03:09 pm, Mike Isely wrote:
> Suggestions are welcome.

Can't offer you any suggestions, but in case it helps, here's a snippet from 
my dmseg output after unplugging the power for a few seconds:
[257568.056025] usb 1-6: new high speed USB device using ehci_hcd and address 
10
[257568.170331] usb 1-6: New USB device found, idVendor=2040, idProduct=2900
[257568.170358] usb 1-6: New USB device strings: Mfr=0, Product=0, 
SerialNumber=0
[257568.170510] usb 1-6: configuration #1 chosen from 1 choice
[257568.171132] usb 1-6: firmware: requesting v4l-pvrusb2-29xxx-01.fw
[257568.245301] pvrusb2: Device microcontroller firmware (re)loaded; it should 
now reset and reconnect.
[257568.275026] usb 1-6: USB disconnect, address 10
[257568.275079] pvrusb2: Device being rendered inoperable
[257569.980770] usb 1-6: new high speed USB device using ehci_hcd and address 
11
[257570.095337] usb 1-6: New USB device found, idVendor=2040, idProduct=2900
[257570.095365] usb 1-6: New USB device strings: Mfr=1, Product=2, 
SerialNumber=0
[257570.095377] usb 1-6: Product: USB Device
[257570.095386] usb 1-6: Manufacturer: Hauppauge
[257570.095567] usb 1-6: configuration #1 chosen from 1 choice
[257570.096749] pvrusb2: Binding ir_video to i2c address 0x18.
[257570.254048] saa7115 1-0021: saa7115 found (1f7115d0e100000) @ 0x42 
(pvrusb2_a)
[257570.402144] pvrusb2: Attached sub-driver saa7115
[257570.412020] msp3400 1-0040: MSP3445G-B8 found @ 0x80 (pvrusb2_a)
[257570.412046] msp3400 1-0040: msp3400 supports radio, mode is autodetect and 
autoselect
[257570.412125] pvrusb2: Attached sub-driver msp3400
[257570.447743] tuner 1-0061: chip found @ 0xc2 (pvrusb2_a)
[257570.447774] pvrusb2: Attached sub-driver tuner
[257570.458140] tuner 1-0043: chip found @ 0x86 (pvrusb2_a)
[257570.458256] tda9887 1-0043: creating new instance
[257570.458266] tda9887 1-0043: tda988[5/6/7] found
[257570.459379] pvrusb2: Attached sub-driver tuner
[257570.481882] tveeprom 1-0050: Hauppauge model 29032, rev D1A3, serial# 
8134662
[257570.481911] tveeprom 1-0050: tuner model is TCL MFNM05-4 (idx 103, type 
43)
[257570.481923] tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
[257570.481934] tveeprom 1-0050: audio processor is MSP3445 (idx 12)
[257570.481945] tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
[257570.481956] tveeprom 1-0050: has radio, has IR receiver, has no IR 
transmitter
[257570.481972] pvrusb2: Supported video standard(s) reported available in 
hardware: PAL-M/N/Nc;NTSC-M/Mj/Mk
[257570.481986] pvrusb2: Mapping standards mask=0xb700 (PAL-M/N/Nc;NTSC-
M/Mj/Mk)
[257570.481997] pvrusb2: Setting up 6 unique standard(s)
[257570.482026] pvrusb2: Set up standard idx=0 name=PAL-M
[257570.482036] pvrusb2: Set up standard idx=1 name=PAL-N
[257570.482046] pvrusb2: Set up standard idx=2 name=PAL-Nc
[257570.482056] pvrusb2: Set up standard idx=3 name=NTSC-M
[257570.482066] pvrusb2: Set up standard idx=4 name=NTSC-Mj
[257570.482077] pvrusb2: Set up standard idx=5 name=NTSC-Mk
[257570.482088] pvrusb2: Initial video standard guessed as NTSC-M
[257570.482113] pvrusb2: Device initialization completed successfully.
[257570.482254] pvrusb2: registered device video0 [mpeg]
[257570.482302] pvrusb2: registered device radio0 [mpeg]
[257570.483630] usb 1-6: firmware: requesting v4l-cx2341x-enc.fw
[257570.783667] tuner-simple 1-0061: creating new instance
[257570.783690] tuner-simple 1-0061: type set to 43 (Philips NTSC MK3 
(FM1236MK3 or FM1236/F))

The system is OpenSUSE with a 2.6.31.8 x86_64 kernel.

I've now unplugged the pvrusb and will let it sit for a while to cool down and 
let its memory randomize.  Will report back later if the results are 
different.
-- 
Q:  How many Zen masters does it take to screw in a light bulb?
A:  None.  The Universe spins the bulb, and the Zen master stays out
    of the way.