[pvrusb2] firmware problems it seems

[Jeff Sadowski]

Ok so I reinstalled the default kernel modules and
then just installed the pvrusb2 module and then
relised I needed to redo the firmware files so I went
into the utils directory and did fwfind.sh
I had to change the location of some of the commands
(cp and rm are in the bin dir) after running that
twice I had the 2 firmware files I needed. I put thos
in the /lib/firmware directory and then I did a dmesg
-c to clear the dmesg log. Then I proceeded to plug in
the pvrusb2 device.

usb 4-2: new high speed USB device using ehci_hcd and
address 2
usb 4-2: configuration #1 chosen from 1 choice
Linux video capture interface: v1.00
pvrusb2: pvr_init
pvrusb2: pvr2_hdw_create: hdw=f2fe2000, type "WinTV
PVR USB2 Model Category 29xxxx"
pvrusb2: Driver unit number is 0, name is pvrusb2_a
pvrusb2: subsys_stream_mask: 0x1e
pvrusb2: pvr_probe(pvr=f25c8e80)
pvrusb2: pvr2_hdw_setup(hdw=f2fe2000) begin
pvrusb2: USB endpoint config looks strange; possibly
firmware needs to be loaded
pvrusb2: pvr2_upload_firmware1
usbcore: registered new driver pvrusb2
/root/pvrusb2-mci-20060326/driver/pvrusb2-main.c:
Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner :
20060326
(from www.isely.net)
/root/pvrusb2-mci-20060326/driver/pvrusb2-main.c:
Debug mask is 16834943 (0x100e17f)
pvrusb2: Located fx2 controller firmware:
v4l-pvrusb2-29xxx-01.fw; uploading...
pvrusb2: cpureset_assert(1)
pvrusb2: Upload done, releasing device's CPU
pvrusb2: cpureset_assert(0)
pvrusb2: Upload done (8192 bytes sent)
pvrusb2: pvr2_hdw_setup(hdw=f2fe2000) done, ok=1
init_ok=0
pvrusb2: Device microcontroller firmware (re)loaded;
it should now reset and reconnect.
pvrusb2: pvr2_hdw_setup(hdw=f2fe2000) end
usb 4-2: USB disconnect, address 2
pvrusb2: pvr_disconnect(pvr=f25c8e80) BEGIN
pvrusb2: pvr2_hdw_disconnect(hdw=f2fe2000)
pvrusb2: pvr2_hdw_remove_usb_stuff: hdw=f2fe2000
pvrusb2: render_useless
pvrusb2: pvr2_hdw_destroy: hdw=f2fe2000
pvrusb2: pvr_disconnect(pvr=f25c8e80) DONE
usb 4-2: new high speed USB device using ehci_hcd and
address 3
usb 4-2: configuration #1 chosen from 1 choice
pvrusb2: pvr2_hdw_create: hdw=f5bdf000, type "WinTV
PVR USB2 Model Category 29xxxx"
pvrusb2: Driver unit number is 0, name is pvrusb2_a
pvrusb2: subsys_stream_mask: 0x1e
pvrusb2: pvr_probe(pvr=f543c2c0)
pvrusb2: pvr2_hdw_setup(hdw=f5bdf000) begin
pvrusb2: Probe of device endpoint 1 succeeded
pvrusb2: Performing a device reset...
usb 4-2: reset high speed USB device using ehci_hcd
and address 3
pvrusb2: Requesting powerup
pvrusb2: pvr2_upload_firmware2
pvrusb2: Located encoder firmware: v4l-cx2341x-enc.fw;
uploading...
pvrusb2: Requesting uproc hard reset
pvrusb2: upload of v4l-cx2341x-enc.fw : 262144 /
262144
pvrusb2: i2c_attach [client=tveeprom @ 0x50
ctxt=f4287bc0]
msp3400 1-0040: MSP3445G-B8 found @ 0x80 (pvrusb2_a)
msp3400 1-0040: MSP3445G-B8 supports radio, mode is
autodetect and autoselect
pvrusb2: i2c_attach [client=MSP3445G-B8 @ 0x40
ctxt=f25e4240]
saa7115 1-0021: saa7115 found @ 0x42 (pvrusb2_a)
pvrusb2: i2c_attach [client=saa7115 @ 0x21
ctxt=f25e4f00]
tuner 1-0061: chip found @ 0xc2 (pvrusb2_a)
pvrusb2: i2c_attach [client=(tuner unset) @ 0x61
ctxt=f25e4de0]
tda9887 1-0043: chip found @ 0x86 (pvrusb2_a)
pvrusb2: i2c_attach [client=tda9887 @ 0x43
ctxt=f25e4cc0]
pvrusb2: Timed out control-write
pvrusb2: render_useless
msp3400 1-0040: I/O error #0 (read 0x10/0x7e)
pvrusb2: Attempted to execute control transfer when
device not ok
pvrusb2: pvr2_hdw_setup(hdw=f5bdf000) done, ok=0
init_ok=0
pvrusb2: ***WARNING*** pvrusb2 device hardware appears
to be jammed and I can't clear it.
pvrusb2: You might need to power cycle the pvrusb2
device in order to recover.
pvrusb2: pvr2_hdw_setup(hdw=f5bdf000) end
pvrusb2: Attempted to execute control transfer when
device not ok
msp3400 1-0040: I/O error #1 (read 0x10/0x7e)
pvrusb2: Attempted to execute control transfer when
device not ok
msp3400 1-0040: I/O error #2 (read 0x10/0x7e)
msp3400 1-0040: giving up, resetting chip. Sound will
go off, sorry folks :-|
pvrusb2: Attempted to execute control transfer when
device not ok
msp3400 1-0040: chip reset failed


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com