[pvrusb2] HVR1900 noisy video
Martin MAURER
martinmaurer at gmx.at
Sat Jan 22 04:35:30 CST 2011
Hi,
I recently replaced my PVR150 PCI device with the HVR 1900 USB.
The device seems to load fine, and everything is detected as I expected
it. When I do some recording, get very noisy video. Is there anything
that I can try to get rid of it?
Antenna, TV-Cable and all the stuff should be ok, as it worked fine with
PVR150.
To record I do
echo 210250000 > ctl_frequency/cur_val
cat /dev/video0 > test.mpg
For playing the video I use as always before mplayer.
I live in Austria, and therefore use the PAL standard.
Attaching some outputs for debugging purposes.
Replugging/rebooting/using different channels doesn't help.
Kernel 2.6.35
Firmware extracted from latest drivers from Hauppauge
(HVR-19x0_3_1_27238_WHQL.zip)
regards,
Martin
-------------- next part --------------
for i in 'ls'; do echo $i && cat $i/cur_val ; echo "---------------" ; done
ctl_audio_bitrate
224 kbps
---------------
ctl_audio_crc
No CRC
---------------
ctl_audio_emphasis
No Emphasis
---------------
ctl_audio_layer
MPEG-1/2 Layer II
---------------
ctl_audio_mode
Stereo
---------------
ctl_audio_modes_present
Stereo
---------------
ctl_balance
0
---------------
ctl_bass
0
---------------
ctl_brightness
128
---------------
ctl_channel
0
---------------
ctl_contrast
68
---------------
ctl_cropcap_bounds_height
0
---------------
ctl_cropcap_bounds_left
0
---------------
ctl_cropcap_bounds_top
0
---------------
ctl_cropcap_bounds_width
0
---------------
ctl_cropcap_pixel_denominator
0
---------------
ctl_cropcap_pixel_numerator
0
---------------
ctl_crop_height
576
---------------
ctl_crop_left
0
---------------
ctl_crop_top
0
---------------
ctl_crop_width
720
---------------
ctl_freq_table_channel
0
---------------
ctl_freq_table_value
0
---------------
ctl_frequency
210250000
---------------
ctl_hue
0
---------------
ctl_input
television
---------------
ctl_master_state
ready
---------------
ctl_mpeg_audio_mode
Stereo
---------------
ctl_mpeg_audio_mode_extension
Bound 4
---------------
ctl_mute
false
---------------
ctl_resolution_hor
720
---------------
ctl_resolution_ver
576
---------------
ctl_saturation
64
---------------
ctl_signal_present
65535
---------------
ctl_srate
48 kHz
---------------
ctl_streaming_enabled
false
---------------
ctl_stream_type
MPEG-2 Program Stream
---------------
ctl_treble
0
---------------
ctl_usb_speed
High
---------------
ctl_video_aspect
4x3
---------------
ctl_video_b_frames
2
---------------
ctl_video_bitrate
6000000
---------------
ctl_video_bitrate_mode
Variable Bitrate
---------------
ctl_video_bitrate_peak
8000000
---------------
ctl_video_chroma_median_filter_bottom
0
---------------
ctl_video_chroma_median_filter_top
255
---------------
ctl_video_chroma_spatial_filter_type
1D Horizontal
---------------
ctl_video_gop_closure
true
---------------
ctl_video_gop_size
12
---------------
ctl_video_luma_median_filter_bottom
0
---------------
ctl_video_luma_median_filter_top
255
---------------
ctl_video_luma_spatial_filter_type
1D Horizontal
---------------
ctl_video_median_filter_type
Off
---------------
ctl_video_spatial_filter
0
---------------
ctl_video_spatial_filter_mode
Manual
---------------
ctl_video_standard
PAL-B/G
---------------
ctl_video_standard_mask_active
PAL-B PAL-G
---------------
ctl_video_standard_mask_available
PAL-B PAL-B1 PAL-G PAL-H PAL-I PAL-D PAL-D1 PAL-K SECAM-B SECAM-D SECAM-G SECAM-H SECAM-K SECAM-K1 SECAM-L SECAM-LC ATSC-8VS ATSC-16V
---------------
ctl_video_temporal_decimation
0
---------------
ctl_video_temporal_filter
8
---------------
ctl_video_temporal_filter_mode
Manual
---------------
ctl_volume
62000
-------------- next part --------------
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35-23-generic (buildd at palmer) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #41~lucid1-Ubuntu SMP Thu Dec 2 22:30:17 UTC 2010 (Ubuntu 2.6.35-23.41~lucid1-generic 2.6.35.7)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000006ff90000 (usable)
[ 0.000000] BIOS-e820: 000000006ff90000 - 000000006ff9e000 (ACPI data)
[ 0.000000] BIOS-e820: 000000006ff9e000 - 000000006ffd0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000006ffd0000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] DMI present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x6ff90 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask 080000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable)
[ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000006ff90000 (usable)
[ 0.000000] modified: 000000006ff90000 - 000000006ff9e000 (ACPI data)
[ 0.000000] modified: 000000006ff9e000 - 000000006ffd0000 (ACPI NVS)
[ 0.000000] modified: 000000006ffd0000 - 0000000080000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 00c00000
[ 0.000000] found SMP MP-table at [c00ff780] ff780
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037400000 page 2M
[ 0.000000] 0037400000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ 15000-1a000
[ 0.000000] RAMDISK: 375cd000 - 37ff0000
[ 0.000000] Allocated new RAMDISK: 009a9000 - 013cbfc8
[ 0.000000] Move RAMDISK from 00000000375cd000 - 0000000037feffc7 to 009a9000 - 013cbfc7
[ 0.000000] ACPI: RSDP 000fbba0 00024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 6ff90100 0005C (v01 060810 XSDT1613 20100608 MSFT 00000097)
[ 0.000000] ACPI: FACP 6ff90290 000F4 (v03 060810 FACP1613 20100608 MSFT 00000097)
[ 0.000000] ACPI: DSDT 6ff904a0 099D4 (v01 A1537 A1537000 00000000 INTL 20060113)
[ 0.000000] ACPI: FACS 6ff9e000 00040
[ 0.000000] ACPI: APIC 6ff90390 00080 (v01 060810 APIC1613 20100608 MSFT 00000097)
[ 0.000000] ACPI: MCFG 6ff90410 0003C (v01 060810 OEMMCFG 20100608 MSFT 00000097)
[ 0.000000] ACPI: WDRT 6ff90450 00047 (v01 060810 NV-WDRT 20100608 MSFT 00000097)
[ 0.000000] ACPI: OEMB 6ff9e040 0007A (v01 060810 OEMB1613 20100608 MSFT 00000097)
[ 0.000000] ACPI: HPET 6ff99e80 00038 (v01 060810 OEMHPET0 20100608 MSFT 00000097)
[ 0.000000] ACPI: NVHD 6ff9e0c0 00284 (v01 060810 NVHDCP 20100608 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 903MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x0006ff90
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0006ff90
[ 0.000000] On node 0 totalpages: 458527
[ 0.000000] free_area_init_node: node 0, pgdat c0803f00, node_mem_map c13cd200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1808 pages used for memmap
[ 0.000000] HighMem zone: 229506 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] early_res array is doubled to 64 at [16000 - 167ff]
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:7ec00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c2400000 s36416 r0 d20928 u1048576
[ 0.000000] pcpu-alloc: s36416 r0 d20928 u1048576 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 454943
[ 0.000000] Kernel command line: root=UUID=c533efdb-bc6f-45be-bb13-ee84234cf9dd ro quiet splash
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 9172480 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Subtract (51 early reservations)
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE
[ 0.000000] #2 [0000100000 - 00009a485c] TEXT DATA BSS
[ 0.000000] #3 [00009a5000 - 00009a8238] BRK
[ 0.000000] #4 [00000ff790 - 0000100000] BIOS reserved
[ 0.000000] #5 [00000ff780 - 00000ff790] MP-table mpf
[ 0.000000] #6 [000009fc00 - 00000f1310] BIOS reserved
[ 0.000000] #7 [00000f143c - 00000ff780] BIOS reserved
[ 0.000000] #8 [00000f1310 - 00000f143c] MP-table mpc
[ 0.000000] #9 [0000010000 - 0000011000] TRAMPOLINE
[ 0.000000] #10 [0000011000 - 0000015000] ACPI WAKEUP
[ 0.000000] #11 [0000015000 - 0000016000] PGTABLE
[ 0.000000] #12 [00009a9000 - 00013cc000] NEW RAMDISK
[ 0.000000] #13 [00013cc000 - 00013cd000] BOOTMEM
[ 0.000000] #14 [00013cd000 - 00021cd000] BOOTMEM
[ 0.000000] #15 [00021cd000 - 00021cd004] BOOTMEM
[ 0.000000] #16 [00021cd040 - 00021cd100] BOOTMEM
[ 0.000000] #17 [00021cd100 - 00021cd154] BOOTMEM
[ 0.000000] #18 [00021cd180 - 00021d0180] BOOTMEM
[ 0.000000] #19 [00021d0180 - 00021d01d8] BOOTMEM
[ 0.000000] #20 [00021d0200 - 00021d3200] BOOTMEM
[ 0.000000] #21 [00021d3200 - 00021d3225] BOOTMEM
[ 0.000000] #22 [00021d3240 - 00021d3267] BOOTMEM
[ 0.000000] #23 [00021d3280 - 00021d33b4] BOOTMEM
[ 0.000000] #24 [00021d33c0 - 00021d3400] BOOTMEM
[ 0.000000] #25 [00021d3400 - 00021d3440] BOOTMEM
[ 0.000000] #26 [00021d3440 - 00021d3480] BOOTMEM
[ 0.000000] #27 [00021d3480 - 00021d34c0] BOOTMEM
[ 0.000000] #28 [00021d34c0 - 00021d3500] BOOTMEM
[ 0.000000] #29 [00021d3500 - 00021d3540] BOOTMEM
[ 0.000000] #30 [00021d3540 - 00021d3580] BOOTMEM
[ 0.000000] #31 [00021d3580 - 00021d35c0] BOOTMEM
[ 0.000000] #32 [00021d35c0 - 00021d3600] BOOTMEM
[ 0.000000] #33 [00021d3600 - 00021d3640] BOOTMEM
[ 0.000000] #34 [00021d3640 - 00021d3650] BOOTMEM
[ 0.000000] #35 [00021d3680 - 00021d36c0] BOOTMEM
[ 0.000000] #36 [00021d36c0 - 00021d3700] BOOTMEM
[ 0.000000] #37 [0002400000 - 000240e000] BOOTMEM
[ 0.000000] #38 [0002500000 - 000250e000] BOOTMEM
[ 0.000000] #39 [0002600000 - 000260e000] BOOTMEM
[ 0.000000] #40 [0002700000 - 000270e000] BOOTMEM
[ 0.000000] #41 [00021d5700 - 00021d5704] BOOTMEM
[ 0.000000] #42 [00021d5740 - 00021d5744] BOOTMEM
[ 0.000000] #43 [00021d5780 - 00021d5790] BOOTMEM
[ 0.000000] #44 [00021d57c0 - 00021d57d0] BOOTMEM
[ 0.000000] #45 [00021d5800 - 00021d58a0] BOOTMEM
[ 0.000000] #46 [00021d58c0 - 00021d5908] BOOTMEM
[ 0.000000] #47 [00021d5940 - 00021d9940] BOOTMEM
[ 0.000000] #48 [00021d9940 - 0002259940] BOOTMEM
[ 0.000000] #49 [0002259940 - 0002299940] BOOTMEM
[ 0.000000] #50 [000270e000 - 0002fcd600] BOOTMEM
[ 0.000000] Initializing HighMem for node 0 (000377fe:0006ff90)
[ 0.000000] Memory: 1790496k/1834560k available (4931k kernel code, 43612k reserved, 2350k data, 684k init, 925256k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc081d000 - 0xc08c8000 ( 684 kB)
[ 0.000000] .data : 0xc05d0e7e - 0xc081c828 (2350 kB)
[ 0.000000] .text : 0xc0100000 - 0xc05d0e7e (4931 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:712
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1599.780 MHz processor.
[ 0.004011] Calibrating delay loop (skipped), value calculated using timer frequency.. 3199.56 BogoMIPS (lpj=6399120)
[ 0.004023] pid_max: default: 32768 minimum: 301
[ 0.004072] Security Framework initialized
[ 0.004109] AppArmor: AppArmor initialized
[ 0.004113] Yama: becoming mindful.
[ 0.004235] Mount-cache hash table entries: 512
[ 0.004490] Initializing cgroup subsys ns
[ 0.004500] Initializing cgroup subsys cpuacct
[ 0.004511] Initializing cgroup subsys memory
[ 0.004530] Initializing cgroup subsys devices
[ 0.004536] Initializing cgroup subsys freezer
[ 0.004542] Initializing cgroup subsys net_cls
[ 0.004594] CPU: Physical Processor ID: 0
[ 0.004598] CPU: Processor Core ID: 0
[ 0.004604] mce: CPU supports 5 MCE banks
[ 0.004618] CPU0: Thermal monitoring enabled (TM2)
[ 0.004627] using mwait in idle threads.
[ 0.004640] Performance Events: PEBS fmt0+, Atom events, Intel PMU driver.
[ 0.004659] ... version: 3
[ 0.004664] ... bit width: 40
[ 0.004669] ... generic registers: 2
[ 0.004674] ... value mask: 000000ffffffffff
[ 0.004679] ... max period: 000000007fffffff
[ 0.004684] ... fixed-purpose events: 3
[ 0.004689] ... event mask: 0000000700000003
[ 0.011860] ACPI: Core revision 20100428
[ 0.035525] ftrace: converting mcount calls to 0f 1f 44 00 00
[ 0.035537] ftrace: allocating 21766 entries in 43 pages
[ 0.040067] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.040498] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.080192] CPU0: Intel(R) Atom(TM) CPU 330 @ 1.60GHz stepping 02
[ 0.084000] Booting Node 0, Processors #1
[ 0.008000] Initializing CPU#1
[ 0.172198] #2
[ 0.008000] Initializing CPU#2
[ 0.264243] #3 Ok.
[ 0.008000] Initializing CPU#3
[ 0.356023] Brought up 4 CPUs
[ 0.356033] Total of 4 processors activated (12799.41 BogoMIPS).
[ 0.357829] devtmpfs: initialized
[ 0.361715] regulator: core version 0.5
[ 0.361790] Time: 11:20:34 Date: 01/22/11
[ 0.361876] NET: Registered protocol family 16
[ 0.361904] Trying to unpack rootfs image as initramfs...
[ 0.362224] EISA bus registered
[ 0.362249] ACPI: bus type pci registered
[ 0.362413] PCI: MMCONFIG for domain 0000 [bus 00-1f] at [mem 0xfc000000-0xfdffffff] (base 0xfc000000)
[ 0.362422] PCI: not using MMCONFIG
[ 0.362712] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
[ 0.362717] PCI: Using configuration type 1 for base access
[ 0.365127] bio: create slab <bio-0> at 0
[ 0.370441] ACPI: EC: Look up EC in DSDT
[ 0.376580] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.400841] ACPI: Interpreter enabled
[ 0.400851] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.400908] ACPI: Using IOAPIC for interrupt routing
[ 0.401050] PCI: MMCONFIG for domain 0000 [bus 00-1f] at [mem 0xfc000000-0xfdffffff] (base 0xfc000000)
[ 0.407968] PCI: MMCONFIG at [mem 0xfc000000-0xfdffffff] reserved in ACPI motherboard resources
[ 0.407975] PCI: Using MMCONFIG for extended config space
[ 0.451921] ACPI Warning: Incorrect checksum in table [OEMB] - 0x91, should be 0x90 (20100428/tbutils-314)
[ 0.452668] ACPI: No dock devices found.
[ 0.452679] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.453778] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.454624] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
[ 0.454632] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
[ 0.454639] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.454646] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff]
[ 0.454653] pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xfbffffff]
[ 0.454660] pci_root PNP0A03:00: host bridge window [mem 0xfe000000-0xfebfffff]
[ 0.454935] pci 0000:00:03.0: reg 10: [io 0x4f00-0x4fff]
[ 0.455069] pci 0000:00:03.2: reg 10: [io 0x4900-0x493f]
[ 0.455091] pci 0000:00:03.2: reg 20: [io 0x4d00-0x4d3f]
[ 0.455100] pci 0000:00:03.2: reg 24: [io 0x4e00-0x4e3f]
[ 0.455134] pci 0000:00:03.2: PME# supported from D3hot D3cold
[ 0.455144] pci 0000:00:03.2: PME# disabled
[ 0.455298] pci 0000:00:03.5: reg 10: [mem 0xf9f80000-0xf9ffffff]
[ 0.455412] pci 0000:00:04.0: reg 10: [mem 0xf9f7f000-0xf9f7ffff]
[ 0.455457] pci 0000:00:04.0: supports D1 D2
[ 0.455463] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.455470] pci 0000:00:04.0: PME# disabled
[ 0.455508] pci 0000:00:04.1: reg 10: [mem 0xf9f7ec00-0xf9f7ecff]
[ 0.455560] pci 0000:00:04.1: supports D1 D2
[ 0.455566] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.455573] pci 0000:00:04.1: PME# disabled
[ 0.455619] pci 0000:00:06.0: reg 10: [mem 0xf9f7d000-0xf9f7dfff]
[ 0.455665] pci 0000:00:06.0: supports D1 D2
[ 0.455670] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.455677] pci 0000:00:06.0: PME# disabled
[ 0.455715] pci 0000:00:06.1: reg 10: [mem 0xf9f7e800-0xf9f7e8ff]
[ 0.455767] pci 0000:00:06.1: supports D1 D2
[ 0.455772] pci 0000:00:06.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.455780] pci 0000:00:06.1: PME# disabled
[ 0.455826] pci 0000:00:08.0: reg 10: [mem 0xf9f78000-0xf9f7bfff]
[ 0.455877] pci 0000:00:08.0: PME# supported from D3hot D3cold
[ 0.455884] pci 0000:00:08.0: PME# disabled
[ 0.455976] pci 0000:00:0b.0: reg 10: [io 0xc080-0xc087]
[ 0.455985] pci 0000:00:0b.0: reg 14: [io 0xc000-0xc003]
[ 0.455995] pci 0000:00:0b.0: reg 18: [io 0xbc00-0xbc07]
[ 0.456013] pci 0000:00:0b.0: reg 1c: [io 0xb880-0xb883]
[ 0.456023] pci 0000:00:0b.0: reg 20: [io 0xb800-0xb80f]
[ 0.456033] pci 0000:00:0b.0: reg 24: [mem 0xf9f76000-0xf9f77fff]
[ 0.456276] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.456288] pci 0000:00:0c.0: PME# disabled
[ 0.456389] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.456396] pci 0000:00:10.0: PME# disabled
[ 0.456624] pci 0000:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.456636] pci 0000:00:15.0: PME# disabled
[ 0.456886] pci 0000:00:16.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.456898] pci 0000:00:16.0: PME# disabled
[ 0.457025] pci 0000:00:09.0: PCI bridge to [bus 01-01] (subtractive decode)
[ 0.457034] pci 0000:00:09.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.457042] pci 0000:00:09.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.457051] pci 0000:00:09.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.457058] pci 0000:00:09.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.457065] pci 0000:00:09.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.457071] pci 0000:00:09.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.457078] pci 0000:00:09.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[ 0.457085] pci 0000:00:09.0: bridge window [mem 0x80000000-0xfbffffff] (subtractive decode)
[ 0.457092] pci 0000:00:09.0: bridge window [mem 0xfe000000-0xfebfffff] (subtractive decode)
[ 0.457249] pci 0000:00:0c.0: PCI bridge to [bus 02-02]
[ 0.457268] pci 0000:00:0c.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.457281] pci 0000:00:0c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.457301] pci 0000:00:0c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.457372] pci 0000:03:00.0: reg 10: [mem 0xfa000000-0xfaffffff]
[ 0.457389] pci 0000:03:00.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.457405] pci 0000:03:00.0: reg 1c: [mem 0xf6000000-0xf7ffffff 64bit pref]
[ 0.457416] pci 0000:03:00.0: reg 24: [io 0xdc00-0xdc7f]
[ 0.457427] pci 0000:03:00.0: reg 30: [mem 0xfbde0000-0xfbdfffff pref]
[ 0.457500] pci 0000:00:10.0: PCI bridge to [bus 03-03]
[ 0.457509] pci 0000:00:10.0: bridge window [io 0xd000-0xdfff]
[ 0.457516] pci 0000:00:10.0: bridge window [mem 0xfa000000-0xfbdfffff]
[ 0.457526] pci 0000:00:10.0: bridge window [mem 0xe0000000-0xf7ffffff 64bit pref]
[ 0.457712] pci 0000:04:00.0: reg 10: [io 0xe800-0xe8ff]
[ 0.457736] pci 0000:04:00.0: reg 18: [mem 0xf8fff000-0xf8ffffff 64bit pref]
[ 0.457754] pci 0000:04:00.0: reg 20: [mem 0xf8ff8000-0xf8ffbfff 64bit pref]
[ 0.457767] pci 0000:04:00.0: reg 30: [mem 0xfbef0000-0xfbefffff pref]
[ 0.457812] pci 0000:04:00.0: supports D1 D2
[ 0.457817] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.457826] pci 0000:04:00.0: PME# disabled
[ 0.464042] pci 0000:00:15.0: PCI bridge to [bus 04-04]
[ 0.464062] pci 0000:00:15.0: bridge window [io 0xe000-0xefff]
[ 0.464074] pci 0000:00:15.0: bridge window [mem 0xfbe00000-0xfbefffff]
[ 0.464094] pci 0000:00:15.0: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
[ 0.464293] pci 0000:05:00.0: reg 10: [mem 0xfbff0000-0xfbffffff 64bit]
[ 0.464362] pci 0000:05:00.0: supports D1
[ 0.464368] pci 0000:05:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.464376] pci 0000:05:00.0: PME# disabled
[ 0.472033] pci 0000:00:16.0: PCI bridge to [bus 05-05]
[ 0.472053] pci 0000:00:16.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.472066] pci 0000:00:16.0: bridge window [mem 0xfbf00000-0xfbffffff]
[ 0.472085] pci 0000:00:16.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.472141] pci_bus 0000:00: on NUMA node 0
[ 0.472155] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.472651] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IXVE._PRT]
[ 0.472818] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
[ 0.473041] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
[ 0.473229] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[ 0.510219] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[ 0.510873] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
[ 0.511522] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[ 0.512201] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[ 0.512851] ACPI: PCI Interrupt Link [LN0A] (IRQs 16 17 18 19) *0, disabled.
[ 0.513508] ACPI: PCI Interrupt Link [LN0B] (IRQs 16 17 18 19) *0, disabled.
[ 0.514157] ACPI: PCI Interrupt Link [LN0C] (IRQs 16 17 18 19) *0, disabled.
[ 0.514806] ACPI: PCI Interrupt Link [LN0D] (IRQs 16 17 18 19) *0, disabled.
[ 0.515455] ACPI: PCI Interrupt Link [LN1A] (IRQs 16 17 18 19) *0, disabled.
[ 0.516126] ACPI: PCI Interrupt Link [LN1B] (IRQs 16 17 18 19) *0, disabled.
[ 0.516777] ACPI: PCI Interrupt Link [LN1C] (IRQs 16 17 18 19) *0, disabled.
[ 0.517426] ACPI: PCI Interrupt Link [LN1D] (IRQs 16 17 18 19) *0, disabled.
[ 0.518077] ACPI: PCI Interrupt Link [LN2A] (IRQs 16 17 18 19) *0, disabled.
[ 0.518725] ACPI: PCI Interrupt Link [LN2B] (IRQs 16 17 18 19) *0, disabled.
[ 0.519374] ACPI: PCI Interrupt Link [LN2C] (IRQs 16 17 18 19) *0, disabled.
[ 0.520046] ACPI: PCI Interrupt Link [LN2D] (IRQs 16 17 18 19) *0, disabled.
[ 0.520709] ACPI: PCI Interrupt Link [LN3A] (IRQs 16 17 18 19) *11
[ 0.521358] ACPI: PCI Interrupt Link [LN3B] (IRQs 16 17 18 19) *0, disabled.
[ 0.522008] ACPI: PCI Interrupt Link [LN3C] (IRQs 16 17 18 19) *0, disabled.
[ 0.522659] ACPI: PCI Interrupt Link [LN3D] (IRQs 16 17 18 19) *0, disabled.
[ 0.523319] ACPI: PCI Interrupt Link [LN4A] (IRQs 16 17 18 19) *9
[ 0.523977] ACPI: PCI Interrupt Link [LN4B] (IRQs 16 17 18 19) *0, disabled.
[ 0.524640] ACPI: PCI Interrupt Link [LN4C] (IRQs 16 17 18 19) *0, disabled.
[ 0.525293] ACPI: PCI Interrupt Link [LN4D] (IRQs 16 17 18 19) *0, disabled.
[ 0.525944] ACPI: PCI Interrupt Link [LN5A] (IRQs 16 17 18 19) *0, disabled.
[ 0.526594] ACPI: PCI Interrupt Link [LN5B] (IRQs 16 17 18 19) *0, disabled.
[ 0.527246] ACPI: PCI Interrupt Link [LN5C] (IRQs 16 17 18 19) *0, disabled.
[ 0.527903] ACPI: PCI Interrupt Link [LN5D] (IRQs 16 17 18 19) *0, disabled.
[ 0.528570] ACPI: PCI Interrupt Link [LN6A] (IRQs 16 17 18 19) *0, disabled.
[ 0.529222] ACPI: PCI Interrupt Link [LN6B] (IRQs 16 17 18 19) *0, disabled.
[ 0.529872] ACPI: PCI Interrupt Link [LN6C] (IRQs 16 17 18 19) *0, disabled.
[ 0.530523] ACPI: PCI Interrupt Link [LN6D] (IRQs 16 17 18 19) *0, disabled.
[ 0.531183] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *10
[ 0.531840] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *11
[ 0.532515] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
[ 0.533177] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *10
[ 0.533836] ACPI: PCI Interrupt Link [SGRU] (IRQs 20 21 22 23) *15
[ 0.534498] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *14
[ 0.535164] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *7
[ 0.535829] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
[ 0.536611] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 0.537300] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *9
[ 0.537961] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *15
[ 0.538627] ACPI: PCI Interrupt Link [LRP0] (IRQs 20 21 22 23) *10
[ 0.539283] ACPI: PCI Interrupt Link [LRP1] (IRQs 20 21 22 23) *0, disabled.
[ 0.539941] ACPI: PCI Interrupt Link [LRP2] (IRQs 20 21 22 23) *0, disabled.
[ 0.540618] ACPI: PCI Interrupt Link [LRP3] (IRQs 20 21 22 23) *11
[ 0.541286] ACPI: PCI Interrupt Link [LRP4] (IRQs 20 21 22 23) *9
[ 0.541938] ACPI: PCI Interrupt Link [LRP5] (IRQs 20 21 22 23) *0, disabled.
[ 0.542593] ACPI: PCI Interrupt Link [LRP6] (IRQs 20 21 22 23) *0, disabled.
[ 0.542732] HEST: Table is not found!
[ 0.542963] vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.542972] vgaarb: loaded
[ 0.543380] SCSI subsystem initialized
[ 0.543414] libata version 3.00 loaded.
[ 0.543414] usbcore: registered new interface driver usbfs
[ 0.543414] usbcore: registered new interface driver hub
[ 0.544052] usbcore: registered new device driver usb
[ 0.544671] ACPI: WMI: Mapper loaded
[ 0.544677] PCI: Using ACPI for IRQ routing
[ 0.544690] PCI: pci_cache_line_size set to 64 bytes
[ 0.544838] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.544845] reserve RAM buffer: 000000006ff90000 - 000000006fffffff
[ 0.545076] NetLabel: Initializing
[ 0.545081] NetLabel: domain hash size = 128
[ 0.545085] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.545114] NetLabel: unlabeled traffic allowed by default
[ 0.545217] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.545235] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31, 31
[ 0.545248] hpet0: 4 comparators, 64-bit 25.000000 MHz counter
[ 0.556131] Switching to clocksource tsc
[ 0.578774] AppArmor: AppArmor Filesystem Enabled
[ 0.578810] pnp: PnP ACPI init
[ 0.578853] ACPI: bus type pnp registered
[ 0.596396] pnp: PnP ACPI: found 12 devices
[ 0.596403] ACPI: ACPI bus type pnp unregistered
[ 0.596411] PnPBIOS: Disabled by ACPI PNP
[ 0.596444] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.596451] system 00:04: [io 0x0800-0x080f] has been reserved
[ 0.596459] system 00:04: [io 0x4000-0x407f] has been reserved
[ 0.596466] system 00:04: [io 0x4080-0x40ff] has been reserved
[ 0.596473] system 00:04: [io 0x4400-0x447f] has been reserved
[ 0.596479] system 00:04: [io 0x4480-0x44ff] has been reserved
[ 0.596486] system 00:04: [io 0x4800-0x487f] has been reserved
[ 0.596493] system 00:04: [io 0x4880-0x48ff] has been reserved
[ 0.596502] system 00:04: [mem 0x000d0000-0x000d3fff window] has been reserved
[ 0.596509] system 00:04: [mem 0x000d4000-0x000d7fff window] has been reserved
[ 0.596517] system 00:04: [mem 0x000de000-0x000dffff window] has been reserved
[ 0.596525] system 00:04: [mem 0xfefe2000-0xfefe3fff] has been reserved
[ 0.596532] system 00:04: [mem 0xfefe1000-0xfefe1fff] has been reserved
[ 0.596539] system 00:04: [mem 0xfee01000-0xfeefffff] has been reserved
[ 0.596556] system 00:07: [io 0x0c00-0x0c0f] has been reserved
[ 0.596562] system 00:07: [io 0x0290-0x029f] has been reserved
[ 0.596569] system 00:07: [io 0x0a20-0x0a2f] has been reserved
[ 0.596576] system 00:07: [io 0x0a30-0x0a3f] has been reserved
[ 0.596590] system 00:08: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.596598] system 00:08: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.596613] system 00:0a: [mem 0xfc000000-0xfdffffff] has been reserved
[ 0.596627] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.596635] system 00:0b: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.596642] system 00:0b: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.596650] system 00:0b: [mem 0x00100000-0x7fffffff] could not be reserved
[ 0.596657] system 00:0b: [mem 0xfec00000-0xffffffff] could not be reserved
[ 0.635827] pci 0000:00:09.0: PCI bridge to [bus 01-01]
[ 0.635834] pci 0000:00:09.0: bridge window [io disabled]
[ 0.635842] pci 0000:00:09.0: bridge window [mem disabled]
[ 0.635849] pci 0000:00:09.0: bridge window [mem pref disabled]
[ 0.635859] pci 0000:00:0c.0: PCI bridge to [bus 02-02]
[ 0.635864] pci 0000:00:0c.0: bridge window [io disabled]
[ 0.635877] pci 0000:00:0c.0: bridge window [mem disabled]
[ 0.635888] pci 0000:00:0c.0: bridge window [mem pref disabled]
[ 0.635907] pci 0000:00:10.0: PCI bridge to [bus 03-03]
[ 0.635914] pci 0000:00:10.0: bridge window [io 0xd000-0xdfff]
[ 0.635923] pci 0000:00:10.0: bridge window [mem 0xfa000000-0xfbdfffff]
[ 0.635931] pci 0000:00:10.0: bridge window [mem 0xe0000000-0xf7ffffff 64bit pref]
[ 0.635941] pci 0000:00:15.0: PCI bridge to [bus 04-04]
[ 0.635950] pci 0000:00:15.0: bridge window [io 0xe000-0xefff]
[ 0.635965] pci 0000:00:15.0: bridge window [mem 0xfbe00000-0xfbefffff]
[ 0.635978] pci 0000:00:15.0: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
[ 0.635997] pci 0000:00:16.0: PCI bridge to [bus 05-05]
[ 0.636001] pci 0000:00:16.0: bridge window [io disabled]
[ 0.636017] pci 0000:00:16.0: bridge window [mem 0xfbf00000-0xfbffffff]
[ 0.636028] pci 0000:00:16.0: bridge window [mem pref disabled]
[ 0.636058] pci 0000:00:09.0: setting latency timer to 64
[ 0.637025] ACPI: PCI Interrupt Link [LRP0] enabled at IRQ 23
[ 0.637037] alloc irq_desc for 23 on node -1
[ 0.637043] alloc kstat_irqs on node -1
[ 0.637059] pci 0000:00:0c.0: PCI INT A -> Link[LRP0] -> GSI 23 (level, low) -> IRQ 23
[ 0.637073] pci 0000:00:0c.0: setting latency timer to 64
[ 0.637091] pci 0000:00:10.0: setting latency timer to 64
[ 0.638004] ACPI: PCI Interrupt Link [LRP3] enabled at IRQ 22
[ 0.638013] alloc irq_desc for 22 on node -1
[ 0.638018] alloc kstat_irqs on node -1
[ 0.638029] pci 0000:00:15.0: PCI INT A -> Link[LRP3] -> GSI 22 (level, low) -> IRQ 22
[ 0.638043] pci 0000:00:15.0: setting latency timer to 64
[ 0.638979] ACPI: PCI Interrupt Link [LRP4] enabled at IRQ 21
[ 0.638987] alloc irq_desc for 21 on node -1
[ 0.638992] alloc kstat_irqs on node -1
[ 0.639003] pci 0000:00:16.0: PCI INT A -> Link[LRP4] -> GSI 21 (level, low) -> IRQ 21
[ 0.639017] pci 0000:00:16.0: setting latency timer to 64
[ 0.639029] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.639035] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.639041] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.639049] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.639060] pci_bus 0000:00: resource 8 [mem 0x80000000-0xfbffffff]
[ 0.639068] pci_bus 0000:00: resource 9 [mem 0xfe000000-0xfebfffff]
[ 0.639075] pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
[ 0.639081] pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
[ 0.639087] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.639093] pci_bus 0000:01: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.639099] pci_bus 0000:01: resource 8 [mem 0x80000000-0xfbffffff]
[ 0.639106] pci_bus 0000:01: resource 9 [mem 0xfe000000-0xfebfffff]
[ 0.639112] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
[ 0.639119] pci_bus 0000:03: resource 1 [mem 0xfa000000-0xfbdfffff]
[ 0.639125] pci_bus 0000:03: resource 2 [mem 0xe0000000-0xf7ffffff 64bit pref]
[ 0.639132] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.639138] pci_bus 0000:04: resource 1 [mem 0xfbe00000-0xfbefffff]
[ 0.639144] pci_bus 0000:04: resource 2 [mem 0xf8f00000-0xf8ffffff 64bit pref]
[ 0.639151] pci_bus 0000:05: resource 1 [mem 0xfbf00000-0xfbffffff]
[ 0.639230] NET: Registered protocol family 2
[ 0.639381] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.639978] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.640942] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.641385] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.641391] TCP reno registered
[ 0.641400] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.641420] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.641651] NET: Registered protocol family 1
[ 0.735121] pci 0000:03:00.0: Boot video device
[ 0.735138] PCI: CLS 64 bytes, default 64
[ 0.735883] cpufreq-nforce2: No nForce2 chipset.
[ 0.735962] Scanning for low memory corruption every 60 seconds
[ 0.736227] audit: initializing netlink socket (disabled)
[ 0.736251] type=2000 audit(1295695233.732:1): initialized
[ 0.755882] highmem bounce pool size: 64 pages
[ 0.755895] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.759593] VFS: Disk quotas dquot_6.5.2
[ 0.759742] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.761230] fuse init (API version 7.14)
[ 0.761473] msgmni has been set to 1689
[ 0.762590] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.762599] io scheduler noop registered
[ 0.762603] io scheduler deadline registered
[ 0.762639] io scheduler cfq registered (default)
[ 0.762908] pcieport 0000:00:0c.0: setting latency timer to 64
[ 0.763043] alloc irq_desc for 40 on node -1
[ 0.763049] alloc kstat_irqs on node -1
[ 0.763095] pcieport 0000:00:0c.0: irq 40 for MSI/MSI-X
[ 0.763307] pcieport 0000:00:15.0: setting latency timer to 64
[ 0.763432] alloc irq_desc for 41 on node -1
[ 0.763436] alloc kstat_irqs on node -1
[ 0.763461] pcieport 0000:00:15.0: irq 41 for MSI/MSI-X
[ 0.763653] pcieport 0000:00:16.0: setting latency timer to 64
[ 0.763779] alloc irq_desc for 42 on node -1
[ 0.763783] alloc kstat_irqs on node -1
[ 0.763808] pcieport 0000:00:16.0: irq 42 for MSI/MSI-X
[ 0.764041] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.764102] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.764328] intel_idle: MWAIT substates: 0x10
[ 0.764333] intel_idle: v0.4 model 0x1C
[ 0.764337] intel_idle: lapic_timer_reliable_states 0x6
[ 0.764661] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.764674] ACPI: Power Button [PWRB]
[ 0.764816] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.764825] ACPI: Power Button [PWRF]
[ 0.765576] ACPI: acpi_idle yielding to intel_idle
[ 0.782623] ERST: Table is not found!
[ 0.782842] isapnp: Scanning for PnP cards...
[ 0.783401] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.783571] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.784257] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.787378] brd: module loaded
[ 0.788836] loop: module loaded
[ 0.790351] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 20
[ 0.790365] alloc irq_desc for 20 on node -1
[ 0.790371] alloc kstat_irqs on node -1
[ 0.790387] pata_acpi 0000:00:0b.0: PCI INT A -> Link[LSA0] -> GSI 20 (level, low) -> IRQ 20
[ 0.790446] pata_acpi 0000:00:0b.0: setting latency timer to 64
[ 0.790472] pata_acpi 0000:00:0b.0: PCI INT A disabled
[ 0.791390] Fixed MDIO Bus: probed
[ 0.791486] PPP generic driver version 2.4.2
[ 0.791614] tun: Universal TUN/TAP device driver, 1.6
[ 0.791619] tun: (C) 1999-2004 Max Krasnyansky <maxk at qualcomm.com>
[ 0.791842] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.792811] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 23
[ 0.792823] ehci_hcd 0000:00:04.1: PCI INT B -> Link[LUB2] -> GSI 23 (level, low) -> IRQ 23
[ 0.792861] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 0.792869] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 0.792973] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[ 0.793019] ehci_hcd 0000:00:04.1: debug port 1
[ 0.793033] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
[ 0.793073] ehci_hcd 0000:00:04.1: irq 23, io mem 0xf9f7ec00
[ 0.802938] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[ 0.803228] hub 1-0:1.0: USB hub found
[ 0.803242] hub 1-0:1.0: 5 ports detected
[ 0.804317] ACPI: PCI Interrupt Link [UB12] enabled at IRQ 22
[ 0.804330] ehci_hcd 0000:00:06.1: PCI INT B -> Link[UB12] -> GSI 22 (level, low) -> IRQ 22
[ 0.804364] ehci_hcd 0000:00:06.1: setting latency timer to 64
[ 0.804371] ehci_hcd 0000:00:06.1: EHCI Host Controller
[ 0.804485] ehci_hcd 0000:00:06.1: new USB bus registered, assigned bus number 2
[ 0.804532] ehci_hcd 0000:00:06.1: debug port 1
[ 0.804545] ehci_hcd 0000:00:06.1: cache line size of 64 is not supported
[ 0.804581] ehci_hcd 0000:00:06.1: irq 22, io mem 0xf9f7e800
[ 0.814937] ehci_hcd 0000:00:06.1: USB 2.0 started, EHCI 1.00
[ 0.815235] hub 2-0:1.0: USB hub found
[ 0.815248] hub 2-0:1.0: 6 ports detected
[ 0.815407] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.816379] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
[ 0.816391] ohci_hcd 0000:00:04.0: PCI INT A -> Link[LUB0] -> GSI 21 (level, low) -> IRQ 21
[ 0.816424] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 0.816432] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 0.816544] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 3
[ 0.816595] ohci_hcd 0000:00:04.0: irq 21, io mem 0xf9f7f000
[ 0.873199] hub 3-0:1.0: USB hub found
[ 0.873214] hub 3-0:1.0: 5 ports detected
[ 0.874279] ACPI: PCI Interrupt Link [UB11] enabled at IRQ 20
[ 0.874291] ohci_hcd 0000:00:06.0: PCI INT A -> Link[UB11] -> GSI 20 (level, low) -> IRQ 20
[ 0.874322] ohci_hcd 0000:00:06.0: setting latency timer to 64
[ 0.874329] ohci_hcd 0000:00:06.0: OHCI Host Controller
[ 0.874445] ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 4
[ 0.874503] ohci_hcd 0000:00:06.0: irq 20, io mem 0xf9f7d000
[ 0.929402] hub 4-0:1.0: USB hub found
[ 0.929424] hub 4-0:1.0: 6 ports detected
[ 0.929642] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.929933] PNP: No PS/2 controller found. Probing ports directly.
[ 0.930524] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.930548] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.930820] mice: PS/2 mouse device common for all mice
[ 0.931208] rtc_cmos 00:06: RTC can wake from S4
[ 0.931345] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 0.931419] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 0.931824] device-mapper: uevent: version 1.0.3
[ 0.932230] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel at redhat.com
[ 0.932645] device-mapper: multipath: version 1.1.1 loaded
[ 0.932655] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.933079] EISA: Probing bus 0 at eisa.0
[ 0.933088] EISA: Cannot allocate resource for mainboard
[ 0.933098] Cannot allocate resource for EISA slot 1
[ 0.933106] Cannot allocate resource for EISA slot 2
[ 0.933114] Cannot allocate resource for EISA slot 3
[ 0.933122] Cannot allocate resource for EISA slot 4
[ 0.933130] Cannot allocate resource for EISA slot 5
[ 0.933138] Cannot allocate resource for EISA slot 6
[ 0.933147] Cannot allocate resource for EISA slot 7
[ 0.933155] Cannot allocate resource for EISA slot 8
[ 0.933161] EISA: Detected 0 cards.
[ 0.934012] cpuidle: using governor ladder
[ 0.934466] cpuidle: using governor menu
[ 0.935415] TCP cubic registered
[ 0.935901] NET: Registered protocol family 10
[ 0.937095] lo: Disabled Privacy Extensions
[ 0.937824] NET: Registered protocol family 17
[ 0.937991] Using IPI No-Shortcut mode
[ 0.938323] PM: Resume from disk failed.
[ 0.938357] registered taskstats version 1
[ 0.939026] Magic number: 11:59:328
[ 0.939299] rtc_cmos 00:06: setting system clock to 2011-01-22 11:20:34 UTC (1295695234)
[ 0.939310] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.939315] EDD information not available.
[ 1.007883] Freeing initrd memory: 10380k freed
[ 1.067128] usb 1-4: new high speed USB device using ehci_hcd and address 2
[ 1.136155] isapnp: No Plug & Play device found
[ 1.136208] Freeing unused kernel memory: 684k freed
[ 1.136890] Write protecting the kernel text: 4932k
[ 1.136963] Write protecting the kernel read-only data: 1992k
[ 1.193079] Initializing USB Mass Storage driver...
[ 1.193165] usbcore: registered new interface driver usb-storage
[ 1.193170] USB Mass Storage support registered.
[ 1.200195] udev: starting version 151
[ 1.205330] scsi0 : usb-storage 1-4:1.0
[ 1.320659] usb 2-3: new high speed USB device using ehci_hcd and address 2
[ 1.418694] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.420644] ACPI: PCI Interrupt Link [LN3A] enabled at IRQ 19
[ 1.420663] alloc irq_desc for 19 on node -1
[ 1.420670] alloc kstat_irqs on node -1
[ 1.420695] r8169 0000:04:00.0: PCI INT A -> Link[LN3A] -> GSI 19 (level, low) -> IRQ 19
[ 1.420779] r8169 0000:04:00.0: setting latency timer to 64
[ 1.420838] alloc irq_desc for 43 on node -1
[ 1.420846] alloc kstat_irqs on node -1
[ 1.420871] r8169 0000:04:00.0: irq 43 for MSI/MSI-X
[ 1.422517] r8169 0000:04:00.0: eth0: RTL8168d/8111d at 0xf80b6000, 20:cf:30:c1:9c:95, XID 083000c0 IRQ 43
[ 1.458353] Linux agpgart interface v0.103
[ 1.467290] ahci 0000:00:0b.0: version 3.0
[ 1.467329] ahci 0000:00:0b.0: PCI INT A -> Link[LSA0] -> GSI 20 (level, low) -> IRQ 20
[ 1.468291] alloc irq_desc for 44 on node -1
[ 1.468300] alloc kstat_irqs on node -1
[ 1.468325] ahci 0000:00:0b.0: irq 44 for MSI/MSI-X
[ 1.468341] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP
[ 1.468491] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0xf impl IDE mode
[ 1.468503] ahci 0000:00:0b.0: flags: 64bit ncq sntf led pio slum part sxs
[ 1.468595] ahci 0000:00:0b.0: setting latency timer to 64
[ 1.478272] scsi1 : ahci
[ 1.479052] scsi2 : ahci
[ 1.479592] scsi3 : ahci
[ 1.480055] scsi4 : ahci
[ 1.480527] scsi5 : ahci
[ 1.480990] scsi6 : ahci
[ 1.481744] ata1: SATA max UDMA/133 abar m8192 at 0xf9f76000 port 0xf9f76100 irq 44
[ 1.481758] ata2: SATA max UDMA/133 abar m8192 at 0xf9f76000 port 0xf9f76180 irq 44
[ 1.481768] ata3: SATA max UDMA/133 abar m8192 at 0xf9f76000 port 0xf9f76200 irq 44
[ 1.481779] ata4: SATA max UDMA/133 abar m8192 at 0xf9f76000 port 0xf9f76280 irq 44
[ 1.481787] ata5: DUMMY
[ 1.481793] ata6: DUMMY
[ 1.547686] [drm] Initialized drm 1.1.0 20060810
[ 1.800043] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.804036] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.804081] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.809032] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.840049] usb 4-4: new low speed USB device using ohci_hcd and address 2
[ 1.907358] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 23
[ 1.907373] nouveau 0000:03:00.0: PCI INT A -> Link[SGRU] -> GSI 23 (level, low) -> IRQ 23
[ 1.907385] nouveau 0000:03:00.0: setting latency timer to 64
[ 1.913302] [drm] nouveau 0000:03:00.0: Detected an NV50 generation card (0x0ace80b1)
[ 1.923239] [drm] nouveau 0000:03:00.0: Attempting to load BIOS image from PRAMIN
[ 1.987917] [drm] nouveau 0000:03:00.0: ... appears to be valid
[ 1.987928] [drm] nouveau 0000:03:00.0: BIT BIOS found
[ 1.987935] [drm] nouveau 0000:03:00.0: Bios version 62.79.67.00
[ 1.987944] [drm] nouveau 0000:03:00.0: TMDS table revision 2.0 not currently supported
[ 1.987951] [drm] nouveau 0000:03:00.0: Found Display Configuration Block version 4.0
[ 1.987958] [drm] nouveau 0000:03:00.0: Raw DCB entry 0: 02000300 0000001e
[ 1.987965] [drm] nouveau 0000:03:00.0: Raw DCB entry 1: 02011332 00020010
[ 1.987971] [drm] nouveau 0000:03:00.0: Raw DCB entry 2: 0001133e 00020010
[ 1.987979] [drm] nouveau 0000:03:00.0: DCB connector table: VHER 0x40 5 16 4
[ 1.987986] [drm] nouveau 0000:03:00.0: 0: 0x00000000: type 0x00 idx 0 tag 0xff
[ 1.987994] [drm] nouveau 0000:03:00.0: 1: 0x00001161: type 0x61 idx 1 tag 0x07
[ 1.997349] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 0 at offset 0xDEFA
[ 2.088152] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 1 at offset 0xE1D2
[ 2.088160] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 2 at offset 0xE1D4
[ 2.088174] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 3 at offset 0xE295
[ 2.088191] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 4 at offset 0xE35A
[ 2.088197] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table at offset 0xE3BF
[ 2.110787] usbcore: registered new interface driver hiddev
[ 2.112550] [drm] nouveau 0000:03:00.0: 0xE3BF: Condition still not met after 20ms, skipping following opcodes
[ 2.112568] [drm] nouveau 0000:03:00.0: 0xC86A: parsing output script 0
[ 2.112592] [drm] nouveau 0000:03:00.0: Detected 256MiB VRAM
[ 2.112597] [drm] nouveau 0000:03:00.0: Stolen system memory at: 0x0070000000
[ 2.118256] input: HID Keyboard Device as /devices/pci0000:00/0000:00:06.0/usb4/4-4/4-4:1.0/input/input2
[ 2.118564] generic-usb 0003:0E6A:6001.0001: input,hidraw0: USB HID v1.10 Keyboard [HID Keyboard Device] on usb-0000:00:06.0-4/input0
[ 2.130388] input: HID Keyboard Device as /devices/pci0000:00/0000:00:06.0/usb4/4-4/4-4:1.1/input/input3
[ 2.130684] generic-usb 0003:0E6A:6001.0002: input,hidraw1: USB HID v1.10 Device [HID Keyboard Device] on usb-0000:00:06.0-4/input1
[ 2.130759] usbcore: registered new interface driver usbhid
[ 2.130768] usbhid: USB HID core driver
[ 2.206606] scsi 0:0:0:0: Direct-Access Kingston DataTraveler G2 1.00 PQ: 0 ANSI: 2
[ 2.208224] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.208470] sd 0:0:0:0: [sda] 31252024 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 2.209463] sd 0:0:0:0: [sda] Write Protect is off
[ 2.209472] sd 0:0:0:0: [sda] Mode Sense: 16 24 09 51
[ 2.209479] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 2.212108] [TTM] Zone kernel: Available graphics memory: 438152 kiB.
[ 2.212114] [TTM] Zone highmem: Available graphics memory: 900780 kiB.
[ 2.212119] [TTM] Initializing pool allocator.
[ 2.212461] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 2.212488] sda: sda1
[ 2.216518] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 2.216534] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 2.243784] [drm] nouveau 0000:03:00.0: 512 MiB GART (aperture)
[ 2.244765] [drm] nouveau 0000:03:00.0: Allocating FIFO number 1
[ 2.250602] [drm] nouveau 0000:03:00.0: nouveau_channel_alloc: initialised FIFO 1
[ 2.251691] [drm] nouveau 0000:03:00.0: Detected a DAC output
[ 2.251703] [drm] nouveau 0000:03:00.0: Detected a TMDS output
[ 2.251710] [drm] nouveau 0000:03:00.0: Detected a VGA connector
[ 2.251852] [drm] nouveau 0000:03:00.0: Detected a HDMI connector
[ 2.321118] No connectors reported connected with modes
[ 2.321129] [drm] Cannot find any crtc or sizes - going 1024x768
[ 2.322183] [drm] nouveau 0000:03:00.0: allocated 1024x768 fb: 0x40250000, bo f6607000
[ 2.324153] Console: switching to colour frame buffer device 128x48
[ 2.325245] fb0: nouveaufb frame buffer device
[ 2.325250] drm: registered panic notifier
[ 2.325257] Slow work thread pool: Starting up
[ 2.325414] Slow work thread pool: Ready
[ 2.325436] [drm] Initialized nouveau 0.0.16 20090420 for 0000:03:00.0 on minor 0
[ 5.280037] usb 1-2: new high speed USB device using ehci_hcd and address 3
[ 5.414826] scsi7 : usb-storage 1-2:1.0
[ 6.414173] scsi 7:0:0:0: Direct-Access DMI HD103UJ 1.00 PQ: 0 ANSI: 4
[ 6.415830] sd 7:0:0:0: Attached scsi generic sg1 type 0
[ 6.416145] sd 7:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 6.418035] sd 7:0:0:0: [sdb] Write Protect is off
[ 6.418044] sd 7:0:0:0: [sdb] Mode Sense: 00 26 00 00
[ 6.418051] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 6.420000] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 6.420027] sdb: sdb1
[ 6.509057] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 6.509072] sd 7:0:0:0: [sdb] Attached SCSI disk
[ 7.658330] EXT3-fs: barriers not enabled
[ 7.659141] kjournald starting. Commit interval 5 seconds
[ 7.659190] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 12.421422] EXT3-fs (sda1): using internal journal
[ 12.422885] udev: starting version 151
[ 12.644789] ACPI: resource nForce2_smbus [io 0x4d00-0x4d3f] conflicts with ACPI region SM00 [??? 0x00004d00-0x00004d3f flags 0x30]
[ 12.644801] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 12.644919] i2c i2c-2: nForce2 SMBus adapter at 0x4e00
[ 12.659923] lp: driver loaded but no devices found
[ 12.863645] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 12.869577] udev: renamed network interface eth0 to eth4
[ 12.923901] coretemp coretemp.0: Unable to read TjMax from CPU.
[ 12.929210] coretemp coretemp.1: Unable to read TjMax from CPU.
[ 13.017070] Linux video capture interface: v2.00
[ 13.199751] pvrusb2: Hardware description: WinTV HVR-1900 Model 73xxx
[ 13.207244] usbcore: registered new interface driver pvrusb2
[ 13.207255] pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner
[ 13.207263] pvrusb2: Debug mask is 31 (0x1f)
[ 13.247434] pvrusb2: Binding ir_video to i2c address 0x71.
[ 13.262099] type=1400 audit(1295691646.817:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=749 comm="apparmor_parser"
[ 13.262966] type=1400 audit(1295691646.817:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=749 comm="apparmor_parser"
[ 13.263496] type=1400 audit(1295691646.817:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=749 comm="apparmor_parser"
[ 13.277420] type=1400 audit(1295691646.833:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=756 comm="apparmor_parser"
[ 13.281272] type=1400 audit(1295691646.837:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=756 comm="apparmor_parser"
[ 13.281829] type=1400 audit(1295691646.837:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=756 comm="apparmor_parser"
[ 13.285048] cx25840 3-0044: cx25843-24 found @ 0x88 (pvrusb2_a)
[ 13.285922] pvrusb2: Attached sub-driver cx25840
[ 13.390528] tuner 3-0042: chip found @ 0x84 (pvrusb2_a)
[ 13.390551] pvrusb2: Attached sub-driver tuner
[ 13.492873] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
[ 13.493074] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
[ 13.494375] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[ 13.494394] HDA Intel 0000:00:08.0: PCI INT A -> Link[LAZA] -> GSI 22 (level, low) -> IRQ 22
[ 13.494408] hda_intel: Disable MSI for Nvidia chipset
[ 13.494496] HDA Intel 0000:00:08.0: setting latency timer to 64
[ 13.542584] type=1400 audit(1295691647.097:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=755 comm="apparmor_parser"
[ 13.571404] r8169 0000:04:00.0: eth4: link up
[ 13.571424] r8169 0000:04:00.0: eth4: link up
[ 13.589802] type=1400 audit(1295691647.145:9): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/ntpd" pid=759 comm="apparmor_parser"
[ 13.975786] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[ 14.137428] type=1400 audit(1295691648.097:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/mysqld" pid=987 comm="apparmor_parser"
[ 14.138007] type=1400 audit(1295691648.097:11): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=985 comm="apparmor_parser"
[ 14.362302] ttyS1: LSR safety check engaged!
[ 14.363714] ttyS1: LSR safety check engaged!
[ 14.433552] hda_codec: ALC887: BIOS auto-probing.
[ 14.520717] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 14.520728] apm: disabled - APM is not SMP safe.
[ 15.929712] cx25840 3-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
[ 16.028218] tveeprom 3-00a2: Hauppauge model 73219, rev D1F5, serial# 7116487
[ 16.028228] tveeprom 3-00a2: MAC address is 00:0d:fe:6c:96:c7
[ 16.028236] tveeprom 3-00a2: tuner model is NXP 18271C2 (idx 155, type 54)
[ 16.028246] tveeprom 3-00a2: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
[ 16.028255] tveeprom 3-00a2: audio processor is CX25843 (idx 37)
[ 16.028263] tveeprom 3-00a2: decoder processor is CX25843 (idx 30)
[ 16.028270] tveeprom 3-00a2: has radio, has IR receiver, has IR transmitter
[ 16.028288] pvrusb2: Supported video standard(s) reported available in hardware: PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K
[ 16.028305] pvrusb2: Mapping standards mask=0x3ff00ff (PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K1/L/LC;ATSC-8VSB/16VSB)
[ 16.028314] pvrusb2: Setting up 20 unique standard(s)
[ 16.028326] pvrusb2: Set up standard idx=0 name=PAL-B/G
[ 16.028334] pvrusb2: Set up standard idx=1 name=PAL-D/K
[ 16.028341] pvrusb2: Set up standard idx=2 name=SECAM-B/G
[ 16.028349] pvrusb2: Set up standard idx=3 name=SECAM-D/K
[ 16.028356] pvrusb2: Set up standard idx=4 name=PAL-B
[ 16.028363] pvrusb2: Set up standard idx=5 name=PAL-B1
[ 16.028370] pvrusb2: Set up standard idx=6 name=PAL-G
[ 16.028377] pvrusb2: Set up standard idx=7 name=PAL-H
[ 16.028384] pvrusb2: Set up standard idx=8 name=PAL-I
[ 16.028391] pvrusb2: Set up standard idx=9 name=PAL-D
[ 16.028398] pvrusb2: Set up standard idx=10 name=PAL-D1
[ 16.028405] pvrusb2: Set up standard idx=11 name=PAL-K
[ 16.028412] pvrusb2: Set up standard idx=12 name=SECAM-B
[ 16.028419] pvrusb2: Set up standard idx=13 name=SECAM-D
[ 16.028426] pvrusb2: Set up standard idx=14 name=SECAM-G
[ 16.028433] pvrusb2: Set up standard idx=15 name=SECAM-H
[ 16.028440] pvrusb2: Set up standard idx=16 name=SECAM-K
[ 16.028447] pvrusb2: Set up standard idx=17 name=SECAM-K1
[ 16.028455] pvrusb2: Set up standard idx=18 name=SECAM-L
[ 16.028462] pvrusb2: Set up standard idx=19 name=SECAM-LC
[ 16.028468] pvrusb2: Initial video standard auto-selected to PAL-B/G
[ 16.028489] pvrusb2: Device initialization completed successfully.
[ 16.028681] pvrusb2: registered device video0 [mpeg]
[ 16.028696] DVB: registering new adapter (pvrusb2-dvb)
[ 16.882460] ppdev: user-space parallel port driver
[ 18.593816] cx25840 3-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
[ 18.708569] tda829x 3-0042: setting tuner address to 60
[ 18.874600] tda18271 3-0060: creating new instance
[ 18.917074] TDA18271HD/C2 detected @ 3-0060
[ 20.001113] tda18271: performing RF tracking filter calibration
[ 24.472020] eth4: no IPv6 routers present
[ 41.864953] tda18271: RF tracking filter calibration complete
[ 41.912583] tda829x 3-0042: type set to tda8295+18271
[ 45.816740] cx25840 3-0044: 0x0000 is not a valid video input!
[ 46.030741] DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)...
[ 46.032867] tda829x 3-0042: type set to tda8295
[ 46.073365] tda18271 3-0060: attaching existing instance
[ 84.194337] cx25840 3-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
-------------- next part --------------
mplayer http://192.168.1.5/films/test.mpg
MPlayer SVN-r31918 (C) 2000-2010 MPlayer Team
This codecs.conf is too old and incompatible with this MPlayer release! at line 15
Can't open joystick device /dev/input/js0: No such file or directory
Can't init input joystick
mplayer: could not connect to socket
mplayer: No such file or directory
Failed to open LIRC support. You will not be able to use your remote control.
Playing http://192.168.1.5/films/test.mpg.
Resolving 192.168.1.5 for AF_INET6...
Couldn't resolve name for AF_INET6: 192.168.1.5
Connecting to server 192.168.1.5[192.168.1.5]: 80...
Cache size set to 1024 KBytes
Cache fill: 0.00% (0 bytes)
MPEG-PS file format detected.
VIDEO: MPEG2 720x576 (aspect 2) 25.000 fps 8000.0 kbps (1000.0 kbyte/s)
open: No such file or directory
[MGA] Couldn't open: /dev/mga_vid
open: No such file or directory
[MGA] Couldn't open: /dev/mga_vid
[VO_TDFXFB] This driver only supports the 3Dfx Banshee, Voodoo3 and Voodoo 5.
s3fb: Couldn't map S3 registers: Operation not permitted
Failed to open VDPAU backend libvdpau_nvidia.so: cannot open shared object file: No such file or directory
[vdpau] Error when calling vdp_device_create_x11: 1
==========================================================================
Opening video decoder: [ffmpeg] FFmpeg's libavcodec codec family
Selected video codec: [ffmpeg2] vfm: ffmpeg (FFmpeg MPEG-2)
==========================================================================
==========================================================================
Opening audio decoder: [mp3lib] MPEG layer-2, layer-3
AUDIO: 48000 Hz, 2 ch, s16le, 224.0 kbit/14.58% (ratio: 28000->192000)
Selected audio codec: [mp3] afm: mp3lib (mp3lib MPEG layer-2, layer-3)
==========================================================================
AO: [alsa] 48000Hz 2ch s16le (2 bytes per sample)
Starting playback...
Movie-Aspect is 1.33:1 - prescaling to correct movie aspect.
VO: [xv] 720x576 => 768x576 Planar YV12 [fs]
[mpeg2video @ 0x8ab6bc0]ac-tex damaged at 11 0
[mpeg2video @ 0x8ab6bc0]Warning MVs not available
[mpeg2video @ 0x8ab6bc0]concealing 1620 DC, 1620 AC, 1620 MV errors
A: 2.8 V: 2.8 A-V: -0.004 ct: -0.124 65/ 65 12% 0% 0.5% 0 0 42%
Exiting... (Quit)
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 490 bytes
Desc: This is a digitally signed message part
URL: <http://www.isely.net/pipermail/pvrusb2/attachments/20110122/8dceceec/attachment-0001.pgp>
More information about the pvrusb2
mailing list